Railnet AEI System Site Installation Manual

Site Information

Site Name
Site Number
Track Number
Mile Post
Customer
Job Number
City
State
GPS Coordinates	N W
Team Leader
Installers
Site Contact Name
Site Contact Telephone Number
Site Contact E-Mail Address
APU Primary Telephone Number
APU Secondary Telephone Number
APU IP Address
Site Voice Telephone Number
Installation Completion Date
Customer Service Optimization Date

Other Information

Date phone line(s) installed: __________________

☐ Company (railroad) line

☐ Bell line

Date AC power installed: __________________

System Type

☐ AEI Intermodal DT	☐ AEI Rest. DT	☐ LS Hybrid AEI Rest. DT
☐ AEI Intermodal ST	☐ AEI Rest. ST	☐ LS Hybrid AEI Rest. ST
☐ System 2000E	☐ AEI Unrest. DT	☐ LS Hybrid AEI Unrest. DT
☐ Tracker	☐ AEI Unrest. ST	☐ LS Hybrid AEI Unrest. ST
☐ Other

Equipment Inventory

Antenna Type
Building manufacturer		Serial Number:
APU serial number:
AR2200 Frequency		Serial Number:	Tier
AR2200 Frequency		Serial Number:	Tier
AR2200 Frequency		Serial Number:	Tier
AR2200 Frequency		Serial Number:	Tier
AR2200 Frequency		Serial Number:	Tier
AR2200 Frequency		Serial Number:	Tier
Reno / US Traffic Loop Detector	VDC	Serial Number:
Epic III / Zepic Frequency		Serial Number:

☐	AA3110 Scala Parapanel Antenna 915 MHz		Serial Number: Serial Number:
☐	SRL441P Log Periodic		Serial Number: Serial Number:
☐	SRL470 Log Periodic		Serial Number: Serial Number:
☐	Other	Specify:	Serial Number: Serial Number:
☐	AI1620 / E4 SmartPass	Frequency: Frequency:	Serial Number: Serial Number:
☐	Check Tag AT5720		Serial Number:

Check the appropriate item below:

Protector Panel Type:

☐ SBB2707N1	☐ SBB2707N2	☐ SBB2707N3	☐ SBB2707N5
☐ SBB2707N6	☐ SPI	☐ SuppressSurge	☐ Other. Specify:

Battery Charger Type:

☐ NRS 24/30	☐ Customer Furnished	☐ Other. Specify:

Battery Type:

☐ 4-3VB9 - 80 AMP 24 Volt	☐ 4-3VB11 - 100 AMP 24 Volt	☐ 12AVR-45 Unigy 12 Volt
☐ Customer Furnished	☐ 650A05 Absolyte	☐ Other. Specify:

Wheel Detector Type:

40003237 Dual Servo	400080221 Servo Zero Speed	50-0902 Tiefenbach Dual Head
4000832210 Servo Zero Speed	4000832220 Servo Zero Speed	Customer Furnished

Hut/Enclosure Equipment

Initial each line when completed

_______AC power fail transformer _______Exhaust fan and heater/thermostat

_______Coax cable termination - inside. _______Protection panel checks

_______Door and floor vents open/removed. _______Conduit sealant

Railside Equipment

Initial each line when completed

_______Antenna checks. _______Antenna 0 distance to target rail

_______Splice box (waterproofing). _______Antenna 1 distance to target rail

_______Wheel detector mounting checks. _______Coax cable termination - outside

_______Check tag wiring _______

0 = Right 1 = Left Interference Unit Position (Double Track Only)

System Equipment Setup and Operational Checks

Initial each line when completed:

_______Loop detector and loop operation
_______(2 Second Delay / 2 Second Extend / Sensitivity 0 - 1 / Mode = Infinite)

_______AC power transformer operation
_______Wheel detector setup, operation
_______TDA-105 setup and operation
_______Wheel detector to antenna offset _______ft. Right or Left
_______SmartPass setup and operation
_______AR2200 RF unit(s) operational tests
_______APU-102(s) operational tests
_______Test double track presence
_______Indicate port used for ITC AUX1PORT.DAT or AUX2PORT. DAT or X-Track (Network)

_______Verify ITC/X-Track communication
_______Verify LVD-2000 operation (if equipped)

APU-102 Software Setup and Testing

Initial each line when completed:

_______Initial each line when completed:

_______APU-102 software version ___________

_______Modem card type & serial number:

_______Update site operating parameters

_______Update site session parameters
_______Perform parameters backup
_______Create CF Image
_______Left to right direction: E-W or W-E or N-S or S-N or U-D or D-U

_______Remote support (if possible)
_______Network communications (if applicable)

RF Power Optimization

AVI tier 0	Channel 0	Channel 1
RF PWR at source
Reflected power at source
SWR at source
RF PWR at antenna
Reflected power at antenna
SWR at antenna
Horizontal read lobe
Approximate length of run
Coaxial cable type
Attenuation
Check tag operation
DC input to AR2200	VDC

AVI tier 1	Channel 0	Channel 1
RF PWR at source
Reflected power at source
SWR at source
RF PWR at antenna
Reflected power at antenna
SWR at antenna
Horizontal read lobe
Approximate length of run
Coaxial cable type
Attenuation
Check tag operation
DC input to AR2200	VDC

AVI tier 0	Channel 0	Channel 1
RF PWR at source
Reflected power at source
SWR at source
RF PWR at antenna
Reflected power at antenna
SWR at antenna
Horizontal read lobe
Approximate length of run
Coaxial cable type
Attenuation
Check tag operation
DC input to AR2200	VDC

Site Drawing

Sketch site layout below and include the following:

1) All tracks in immediate area.
2) Direction arrow showing North.
3) Any buildings, metal fences in front of or behind antennas.
4) Overhead high voltage power lines.
5) Transducer location.
6) If double track, detail below with track numbers, i.e. Trk 1/Trk 2. 7) Conduit sizes.