User talk:GMalcom/sandbox - Revision history

JSchultz at 19:19, 19 May 2025

2025-05-19T19:19:25Z

← Older revision		Revision as of 19:19, 19 May 2025
Line 1:		Line 1:
	= Introduction =		= Introduction =
	~~Welcome~~ to the installation guide for your new SensorLink system. This article provides instructions to ensure a safe and efficient installation. Safety is paramount throughout this process. Railroad environments present unique hazards, and strict adherence to all safety protocols is mandatory. Precise workmanship is equally critical for the reliable operation of this SensorLink system. Carefully follow each step, double-check connections, and ensure all components are securely mounted. Your diligence in both safety and workmanship will guarantee a successful and long-lasting installation.<br>		WelcomeX to the installation guide for your new SensorLink system. This article provides instructions to ensure a safe and efficient installation. Safety is paramount throughout this process. Railroad environments present unique hazards, and strict adherence to all safety protocols is mandatory. Precise workmanship is equally critical for the reliable operation of this SensorLink system. Carefully follow each step, double-check connections, and ensure all components are securely mounted. Your diligence in both safety and workmanship will guarantee a successful and long-lasting installation.<br>

	Safety Statement		Safety Statement

DGast: /* Introduction */

2025-05-03T14:06:40Z

Introduction

← Older revision		Revision as of 14:06, 3 May 2025
Line 1:		Line 1:
	= Introduction =		= Introduction =
	Welcome to the installation guide for your new SensorLink system. This article provides instructions to ensure a safe and efficient installation. Safety is paramount throughout this process. Railroad environments present unique hazards, and strict adherence to all safety protocols is mandatory. Precise workmanship is equally critical for the reliable operation of this SensorLink system. Carefully follow each step, double-check connections, and ensure all components are securely mounted. Your diligence in both safety and workmanship will guarantee a successful and long-lasting installation.<br>		Welcome to the installation guide for your new SensorLink system. This article provides instructions to ensure a safe and efficient installation. Safety is paramount throughout this process. Railroad environments present unique hazards, and strict adherence to all safety protocols is mandatory. Precise workmanship is equally critical for the reliable operation of this SensorLink system. Carefully follow each step, double-check connections, and ensure all components are securely mounted. Your diligence in both safety and workmanship will guarantee a successful and long-lasting installation.<br>

			Safety Statement

			Site Work Requirements

	<br>[[Appendix G - Glossary\|Common Vocabulary]]		<br>[[Appendix G - Glossary\|Common Vocabulary]]
	{\| class="wikitable" style="border-collapse: collapse; width: 100%;"		{\| class="wikitable" style="border-collapse: collapse; width: 100%;"

GMalcom: /* Grounding Connections */

2025-04-29T14:50:33Z

Grounding Connections

← Older revision		Revision as of 14:50, 29 April 2025
Line 181:		Line 181:
	*Wire cutter<br>		*Wire cutter<br>
	'''Procedure'''		'''Procedure'''
	#~~Screw ground lug to SensorLink enclosure unistrut.~~		#On the nearside post, partially unscrew the grounding lug's inner bolt and insert copper wire. Secure wire by tightening the inner bolt.
	~~#Partially~~ unscrew the lug's inner bolt and insert copper wire. Secure wire by tightening the inner bolt.
	#Secure wire to grounding rod with grounding rod clamp.		#Secure wire to grounding rod with grounding rod clamp.
	#Cut the copper wire on the excess side of the grounding rod.<br>		#Cut the copper wire on the excess side of the grounding rod.<br>
	#On the farside, screw ground lug to antenna.		#On the farside, screw ground lug to antenna.
	#Repeat steps 2-4 on the farside post.		#Repeat steps 1-3 on the farside post.

	== Solar Panel Connections ==		== Solar Panel Connections ==

GMalcom: /* Presence Subsystem */

2025-04-29T13:54:39Z

Presence Subsystem

← Older revision		Revision as of 13:54, 29 April 2025
Line 168:		Line 168:
	*Cut the sensor wire to length, (with a service loop) and landed in the enclosure '''as shown'''. '''NEED PHOTO/DIAGRAM'''		*Cut the sensor wire to length, (with a service loop) and landed in the enclosure '''as shown'''. '''NEED PHOTO/DIAGRAM'''

	= Presence ~~Subsystem~~ =		= Presence Detector Connections =
	'''Materials Needed'''		'''Materials Needed'''

GMalcom: /* Wheel Sensor */

2025-04-29T13:51:13Z

Wheel Sensor

← Older revision		Revision as of 13:51, 29 April 2025
Line 162:		Line 162:

	= Wheel Sensor =		= Wheel Sensor =
	Refer to [[Frauscher Wheel Detector Installation and Optimization]] for instruction on installing the wheel sensor to the rail. The mounting point on the track should be in line with the antennas as much as possible.~~[[image:img1745544101928.jpeg\|300px\|right\|frameless]]~~		[[image:img1745544101928.jpeg\|300px\|right\|frameless]]

			Refer to [[Frauscher Wheel Detector Installation and Optimization]] for instruction on installing the wheel sensor to the rail. The mounting point on the track should be in line with the antennas as much as possible.
	*Cut the Frauscher's protective hose to the appropriate length and install using the grey cable fitting on the bottom of the enclosure.		*Cut the Frauscher's protective hose to the appropriate length and install using the grey cable fitting on the bottom of the enclosure.
	*Cut the sensor wire to length, (with a service loop) and landed in the enclosure '''as shown'''. '''NEED PHOTO/DIAGRAM'''		*Cut the sensor wire to length, (with a service loop) and landed in the enclosure '''as shown'''. '''NEED PHOTO/DIAGRAM'''

GMalcom: /* Grounding Connections */

2025-04-25T21:05:05Z

Grounding Connections

← Older revision		Revision as of 21:05, 25 April 2025
Line 184:		Line 184:
	#Cut the copper wire on the excess side of the grounding rod.<br>		#Cut the copper wire on the excess side of the grounding rod.<br>
	#On the farside, screw ground lug to antenna.		#On the farside, screw ground lug to antenna.
	#Repeat steps 2-5 on the farside post.		#Repeat steps 2-4 on the farside post.

	== Solar Panel Connections ==		== Solar Panel Connections ==

GMalcom: /* Grounding Connections */

2025-04-25T21:04:25Z

Grounding Connections

← Older revision		Revision as of 21:04, 25 April 2025
Line 184:		Line 184:
	#Cut the copper wire on the excess side of the grounding rod.<br>		#Cut the copper wire on the excess side of the grounding rod.<br>
	#On the farside, screw ground lug to antenna.		#On the farside, screw ground lug to antenna.
	#Repeat steps 2-6 on the farside post.		#Repeat steps 2-5 on the farside post.

	== Solar Panel Connections ==		== Solar Panel Connections ==

GMalcom: /* Grounding Connections */

2025-04-25T21:04:04Z

Grounding Connections

← Older revision		Revision as of 21:04, 25 April 2025
Line 176:		Line 176:
	'''Materials Needed'''		'''Materials Needed'''
	*No. 6 Bare Copper Wire		*No. 6 Bare Copper Wire
	*(2) Cadweld mold ground rod to wire
	*(2) Cadweld mold wire to tower.
	'''Tools Needed'''		'''Tools Needed'''
	*Wire cutter		*Wire cutter<br>
	*Cadweld sparker
	'''Procedure'''		'''Procedure'''
	#Screw ground lug to SensorLink enclosure unistrut.		#Screw ground lug to SensorLink enclosure unistrut.
	#Partially unscrew the lug's inner bolt and insert copper wire. Secure wire by tightening the inner bolt.		#Partially unscrew the lug's inner bolt and insert copper wire. Secure wire by tightening the inner bolt.
	#Secure wire to grounding rod with grounding rod clamp.		#Secure wire to grounding rod with grounding rod clamp.
	~~#Weld the wire to 4x4 post.~~
	~~#Weld the wire to grounding rod.~~
	#Cut the copper wire on the excess side of the grounding rod.<br>		#Cut the copper wire on the excess side of the grounding rod.<br>
	#On the farside, screw ground lug to antenna.		#On the farside, screw ground lug to antenna.

GMalcom: /* Radar Presence Detector */

2025-04-25T20:57:33Z

Radar Presence Detector

← Older revision		Revision as of 20:57, 25 April 2025
Line 124:		Line 124:

	== Radar Presence Detector ==		== Radar Presence Detector ==
	The radar must be attached to ~~where it is~~ facing the rail. '''PHOTO NEEDED, MORE PRODUCT INFO NEEDED'''		The radar must be attached to the nearside post, facing the rail. '''PHOTO NEEDED, MORE PRODUCT INFO NEEDED'''

	*Attach radar facing the track, using provided U-bolts, to nearside post.		*Attach radar facing the track, using provided U-bolts, to nearside post.

GMalcom: /* SensorLink Enclosure */

2025-04-25T20:54:37Z

SensorLink Enclosure

← Older revision		Revision as of 20:54, 25 April 2025
Line 135:		Line 135:
	! style="width: 100%; text-align: center;" \| The SensorLink enclosure is heavy and awkward to handle. Plan your movements, this is a multiple person job.		! style="width: 100%; text-align: center;" \| The SensorLink enclosure is heavy and awkward to handle. Plan your movements, this is a multiple person job.
	\|}		\|}

	Before attaching the enclosure, mark on the nearside post where the enclosure will be attached. Ideal placement of the SensorLink enclosure will ensure accessibility when working inside the enclosure later. The SensorLink enclosure should be attached on the side of the post that is opposite to the track.		Before attaching the enclosure, mark on the nearside post where the enclosure will be attached. Ideal placement of the SensorLink enclosure will ensure accessibility when working inside the enclosure later. The SensorLink enclosure should be attached on the side of the post that is opposite to the track.

	'''[INSERT ORIENTATION DIAGRAM]'''		'''[INSERT ORIENTATION DIAGRAM]'''

	*Attach to nearside post using provided U-Bolts on the side opposite to the track.		*Attach to nearside post using provided U-Bolts on the side of the post opposite to the track.

	<br>		<br>