CINQ Edge Installation Manual - Revision history

JWinkelmann at 14:58, 9 September 2026

2026-09-09T14:58:11Z

← Older revision		Revision as of 14:58, 9 September 2026
Line 154:		Line 154:
	# Drive each grounding rod 2-6 inches from the post, in the loosened soil around the post hole. (Avoid driving the grounding rods into the concrete.		# Drive each grounding rod 2-6 inches from the post, in the loosened soil around the post hole. (Avoid driving the grounding rods into the concrete.
	# Drive the rod until only 4-8 inches remain above grade.		# Drive the rod until only 4-8 inches remain above grade.
	# Cut the grounding wire in half to create two pieces with a terminal on one end. See Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding ~~Installation~~] for details.		# Cut the grounding wire in half to create two pieces with a terminal on one end. See Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding Install] for details.

	=== '''10. Attach antennas''' ===		=== '''10. Attach antennas''' ===
Line 162:		Line 162:
	# Ensure the antenna brand label is upright at the top.		# Ensure the antenna brand label is upright at the top.
	# Use four bolts to secure each antenna to its bracket.		# Use four bolts to secure each antenna to its bracket.
	# Install the grounding‑wire terminal on the lower antenna bracket assembly. See Note 4 on Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding ~~Installation~~].		# Install the grounding‑wire terminal on the lower antenna bracket assembly. See Note 4 on Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding Install].
	# Apply thread lubrication (anti‑seize preferred) to stainless‑steel parapanel hardware to prevent thread galling. See Note 5 on Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (Solar) Connections and Install].		# Apply thread lubrication (anti‑seize preferred) to stainless‑steel parapanel hardware to prevent thread galling. See Note 5 on Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (Solar) Connections and Install].

JWinkelmann at 14:55, 9 September 2026

2026-09-09T14:55:42Z

JWinkelmann at 20:59, 8 September 2026

2026-09-08T20:59:29Z

← Older revision		Revision as of 20:59, 8 September 2026
Line 123:		Line 123:

	=== '''4. Raise enclosure and antenna posts''' ===		=== '''4. Raise enclosure and antenna posts''' ===
	To raise the enclosure post, place the post in the near‑side hole. Ensure correct bracket orientation based on '''Note 11''' in Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 ~~Cinq Edge Solar Install Guide~~], with the strut channel facing away from the track. Keep the post square to the track and level in both directions. Fill the hole with dry concrete, packing it firmly. (Approximately 2.5 bags of 50‑lb concrete are required.) Adding small amounts of water at intervals is recommended.<blockquote>Important! Use magnetic levels to maintain vertical and horizontal alignment.</blockquote>Install the antenna post using the same procedure. See Note 13 on Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 ~~Cinq Edge Solar Install Guide~~]		To raise the enclosure post, place the post in the near‑side hole. Ensure correct bracket orientation based on '''Note 11''' in Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 CINQ EDGE SOLAR INSTALL GUIDE], with the strut channel facing away from the track. Keep the post square to the track and level in both directions. Fill the hole with dry concrete, packing it firmly. (Approximately 2.5 bags of 50‑lb concrete are required.) Adding small amounts of water at intervals is recommended.<blockquote>Important! Use magnetic levels to maintain vertical and horizontal alignment.</blockquote>Install the antenna post using the same procedure. See Note 13 on Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 CINQ EDGE SOLAR INSTALL GUIDE]
	for correct orientation.		for correct orientation.

Line 129:		Line 129:
	Complete the following steps to ensure proper alignment for your hardware:		Complete the following steps to ensure proper alignment for your hardware:

	# Use a 20‑ft Mason’s line to determine the top‑of‑rail (TOR) height. See Drawing [https://docdepot.railrsm.com/images/a/a8/481513_TOR_MEASURING.pdf T.O.R. MEASUREMENT PROCEDURE] for details.		# Use a 20‑ft Mason’s line to determine the top‑of‑rail (TOR) height. See Drawing [https://docdepot.railrsm.com/images/a/a8/481513_TOR_MEASURING.pdf 481513 T.O.R. MEASUREMENT PROCEDURE] for details.
	# Tie the string to the opposite rail, pull it taut across the track, and mark the post at the point where the string touches the top of the rail.		# Tie the string to the opposite rail, pull it taut across the track, and mark the post at the point where the string touches the top of the rail.
	# Measure 31 inches and 53 inches above TOR to mark the antenna bracket locations.<blockquote>'''NOTE:''' If the strut aligns with the antenna bracket height Move the near‑side strut channel location. If adjustment is required, move both the top and bottom strut brackets equally to maintain 30 inches between the outside edges of the strut channel.</blockquote>		# Measure 31 inches and 53 inches above TOR to mark the antenna bracket locations.<blockquote>'''NOTE:''' If the strut aligns with the antenna bracket height Move the near‑side strut channel location. If adjustment is required, move both the top and bottom strut brackets equally to maintain 30 inches between the outside edges of the strut channel.</blockquote>

AShanks: /* 14.3 Connect solar wiring */

2026-09-08T20:34:45Z

14.3 Connect solar wiring

← Older revision		Revision as of 20:34, 8 September 2026
Line 202:		Line 202:

	<div style="border:1px solid #ccc; padding:1em; margin:1em 0; background:#f9f9f9;">		<div style="border:1px solid #ccc; padding:1em; margin:1em 0; background:#f9f9f9;">
	<b>Verify final install checklist</b>		=== <b>Verify final install checklist</b> ===
			Verify the details below before completing installation. See Drawing [[Media:481000.pdf\|481000 CINQ EDGE (SOLAR) FIELD INSTALLATION GUIDE]] for details.
	See Drawing [[Media:481000.pdf\|481000 CINQ EDGE (SOLAR) FIELD INSTALLATION GUIDE]] for details.~~<br>~~
	~~Verify the following details before completing installation:~~
	<ul>		<ul>
	<li>Solar panel orientation faces south or southeast.</li>		<li>Solar panel orientation faces south or southeast.</li>

AShanks: /* 14.3 Connect solar wiring */

2026-09-08T20:33:49Z

14.3 Connect solar wiring

← Older revision		Revision as of 20:33, 8 September 2026
Line 204:		Line 204:
	<b>Verify final install checklist</b>		<b>Verify final install checklist</b>

	See ~~481001_CINQ~~ EDGE SOLAR ~~INSTALL CHECKLIST~~ for details.<br>		See Drawing [[Media:481000.pdf\|481000 CINQ EDGE (SOLAR) FIELD INSTALLATION GUIDE]] for details.<br>
	Verify the following details before completing installation:		Verify the following details before completing installation:
	<ul>		<ul>

AShanks: /* 16. Test system startup */

2026-09-08T20:32:22Z

16. Test system startup

← Older revision		Revision as of 20:32, 8 September 2026
Line 235:		Line 235:

	# Ensure that the battery is charged to 11 V. You can either naturally solar-charge the battery or, for faster results, use a jumper.		# Ensure that the battery is charged to 11 V. You can either naturally solar-charge the battery or, for faster results, use a jumper.
	# Manually test presence detection at the wheel sensor: On the controller board (red PCB in enclosure), ensure that the presence LED is lit green. Trigger presence by swiping a metallic object (for example, a wrench or railroad spike) across the top of the wheel sensor. Verify that the presence LED changes color from green to purple, then blue. '''NOTE:''' The LED remains blue while presence is active (default of two minutes).		# Manually test presence detection at the wheel sensor: On the controller board (red PCB in enclosure), ensure that the presence LED is lit green. Trigger presence by swiping a metallic object (for example, a wrench or railroad spike) across the top of the wheel sensor. Verify that the presence LED changes color from green to purple, then blue. '''NOTE:''' The LED remains blue while presence is active (default of two minutes).
	# Verify that the relay in the lower‑left quadrant of the enclosure activates during the presence test and that its red LED illuminates, indicating that the MPRX is powered.		# Verify that the relay in the lower‑left quadrant of the enclosure activates during the presence test and that its red LED illuminates, indicating that the MPRX is powered.
	# Verify that the power meter in the top‑left of the enclosure displays a non‑zero output between 0.7 W and 2.0 W (typically ~1.4 W) when the MPRX is active.		# Verify that the power meter in the top‑left of the enclosure displays a non‑zero output between 0.7 W and 2.0 W (typically ~1.4 W) when the MPRX is active.

AShanks: /* 13. Connect antennas */

2026-09-08T20:31:03Z

13. Connect antennas

← Older revision		Revision as of 20:31, 8 September 2026
Line 183:		Line 183:

	# Lay out the far‑side antenna conduit. Starting at the near‑side post, run the conduit through the shallow trench under the track and to the bottom of the far‑side post. Coil any slack and lay it neatly against the near‑side post.		# Lay out the far‑side antenna conduit. Starting at the near‑side post, run the conduit through the shallow trench under the track and to the bottom of the far‑side post. Coil any slack and lay it neatly against the near‑side post.
	# On both sides of the track, attach the cables and hoods to the antennas. See Note 6 on ~~481515_CINQ~~ EDGE CONNECTIONS ~~INSTALL~~		# On both sides of the track, attach the cables and hoods to the antennas. See Note 6 on Drawing [[Media:481515.pdf\|481515 CINQ EDGE (SOLAR) CONNECTIONS AND INSTALLATION]].
	# Bury the conduit by filling in the trench.		# Bury the conduit by filling in the trench.

AShanks: /* 11. Install the enclosure */

2026-09-08T20:30:28Z

11. Install the enclosure

← Older revision		Revision as of 20:30, 8 September 2026
Line 173:		Line 173:
	# Slide the second set of cone nuts into the strut channel and center the enclosure.		# Slide the second set of cone nuts into the strut channel and center the enclosure.
	# Adjust the cone nuts vertically if needed.		# Adjust the cone nuts vertically if needed.
	# Secure the bolts from inside the enclosure. See Note 2 on Drawing [[~~File~~:481515.pdf~~\|page=1\|800px~~\|481515 CINQ EDGE (SOLAR) CONNECTIONS AND INSTALLATION]].		# Secure the bolts from inside the enclosure. See Note 2 on Drawing [[Media:481515.pdf\|481515 CINQ EDGE (SOLAR) CONNECTIONS AND INSTALLATION]].

	=== '''12. Install wheel detector''' ===		=== '''12. Install wheel detector''' ===

AShanks: /* 11. Install the enclosure */

2026-09-08T20:29:50Z

11. Install the enclosure

← Older revision		Revision as of 20:29, 8 September 2026
Line 173:		Line 173:
	# Slide the second set of cone nuts into the strut channel and center the enclosure.		# Slide the second set of cone nuts into the strut channel and center the enclosure.
	# Adjust the cone nuts vertically if needed.		# Adjust the cone nuts vertically if needed.
	# Secure the bolts from inside the enclosure. See Note 2 ~~481515_CINQ~~ EDGE CONNECTIONS ~~INSTALL~~		# Secure the bolts from inside the enclosure. See Note 2 on Drawing [[File:481515.pdf\|page=1\|800px\|481515 CINQ EDGE (SOLAR) CONNECTIONS AND INSTALLATION]].

	=== '''12. Install wheel detector''' ===		=== '''12. Install wheel detector''' ===

AShanks: /* 12. Install wheel detector */

2026-09-08T20:29:13Z

12. Install wheel detector

← Older revision		Revision as of 20:29, 8 September 2026
Line 178:		Line 178:
	Install the wheel sensor and clamp, ensuring that the mounting point on the track is aligned with the near-side and far-side poles as closely as possible and located between the two ties.		Install the wheel sensor and clamp, ensuring that the mounting point on the track is aligned with the near-side and far-side poles as closely as possible and located between the two ties.

	See the [[Frauscher Wheel Detector Installation and Optimization\|Frauscher Wheel Detector~~]] [[Frauscher Wheel Detector Installation and Optimization\|~~Installation and Optimization]] topic for detailed instructions.		See the [[Frauscher Wheel Detector Installation and Optimization\|Frauscher Wheel Detector Installation and Optimization]] topic for detailed instructions.

	=== '''13. Connect antennas''' ===		=== '''13. Connect antennas''' ===

← Older revision		Revision as of 14:55, 9 September 2026
Line 101:		Line 101:
	* Take out any boxed items or loose components not attached to the NEMA enclosure and set them aside for later use.		* Take out any boxed items or loose components not attached to the NEMA enclosure and set them aside for later use.

	See Drawing [https://docdepot.railrsm.com/images/d/d1/481403.pdf 481403 Cinq Edge Solar Crate Disassembly] for details on unpacking specific elements of the installation package.		See Drawing [https://docdepot.railrsm.com/images/d/d1/481403.pdf 481403 Cinq Edge (Solar) Crate Disassembly] for details on unpacking specific elements of the installation package.

	=== 2. Position the wheel sensor ===		=== 2. Position the wheel sensor ===
Line 123:		Line 123:

	=== '''4. Raise enclosure and antenna posts''' ===		=== '''4. Raise enclosure and antenna posts''' ===
	To raise the enclosure post, place the post in the near‑side hole. Ensure correct bracket orientation based on '''Note 11''' in Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 ~~CINQ EDGE SOLAR INSTALL GUIDE~~], with the strut channel facing away from the track. Keep the post square to the track and level in both directions. Fill the hole with dry concrete, packing it firmly. (Approximately 2.5 bags of 50‑lb concrete are required.) Adding small amounts of water at intervals is recommended.<blockquote>Important! Use magnetic levels to maintain vertical and horizontal alignment.</blockquote>Install the antenna post using the same procedure. See Note 13 on Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 ~~CINQ EDGE SOLAR INSTALL GUIDE~~]		To raise the enclosure post, place the post in the near‑side hole. Ensure correct bracket orientation based on '''Note 11''' in Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 Cinq Edge (Solar) Install Guide], with the strut channel facing away from the track. Keep the post square to the track and level in both directions. Fill the hole with dry concrete, packing it firmly. (Approximately 2.5 bags of 50‑lb concrete are required.) Adding small amounts of water at intervals is recommended.<blockquote>Important! Use magnetic levels to maintain vertical and horizontal alignment.</blockquote>Install the antenna post using the same procedure. See Note 13 on Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 Cinq Edge (Solar) Install Guide]
	for correct orientation.		for correct orientation.

Line 129:		Line 129:
	Complete the following steps to ensure proper alignment for your hardware:		Complete the following steps to ensure proper alignment for your hardware:

	# Use a 20‑ft Mason’s line to determine the top‑of‑rail (TOR) height. See Drawing [https://docdepot.railrsm.com/images/a/a8/481513_TOR_MEASURING.pdf 481513 T.O.R. ~~MEASUREMENT PROCEDURE~~] for details.		# Use a 20‑ft Mason’s line to determine the top‑of‑rail (TOR) height. See Drawing [https://docdepot.railrsm.com/images/a/a8/481513_TOR_MEASURING.pdf 481513 T.O.R. Measurement Procedure] for details.
	# Tie the string to the opposite rail, pull it taut across the track, and mark the post at the point where the string touches the top of the rail.		# Tie the string to the opposite rail, pull it taut across the track, and mark the post at the point where the string touches the top of the rail.
	# Measure 31 inches and 53 inches above TOR to mark the antenna bracket locations.<blockquote>'''NOTE:''' If the strut aligns with the antenna bracket height Move the near‑side strut channel location. If adjustment is required, move both the top and bottom strut brackets equally to maintain 30 inches between the outside edges of the strut channel.</blockquote>		# Measure 31 inches and 53 inches above TOR to mark the antenna bracket locations.<blockquote>'''NOTE:''' If the strut aligns with the antenna bracket height Move the near‑side strut channel location. If adjustment is required, move both the top and bottom strut brackets equally to maintain 30 inches between the outside edges of the strut channel.</blockquote>

	=== '''6. Attach the solar panel''' ===		=== '''6. Attach the solar panel''' ===
	Position the radar post based on the antenna bracket orientation. See '''Note 13''' on Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 ~~CINQ EDGE~~ (~~SOLAR~~) ~~FIELD INSTALLATION GUIDE~~]		Position the radar post based on the antenna bracket orientation. See '''Note 13''' on Drawing [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 Cinq Edge (Solar) Install Guide]
	for correct orientation. Position the solar panel so it will face south or southeast when the post is raised (see Note 11 solar panel orientation).		for correct orientation. Position the solar panel so it will face south or southeast when the post is raised (see Note 11 solar panel orientation).

	Attach the solar panel to the top of the radar post while the top end of the post is still accessible. See Note 3 on [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 ~~CINQ EDGE~~ (~~SOLAR~~) ~~CONNECTIONS AND INSTALLATION~~]. Support the post so the panel does not rest on the ground.		Attach the solar panel to the top of the radar post while the top end of the post is still accessible. See Note 3 on [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (Solar) Connections and Install]. Support the post so the panel does not rest on the ground.

	[[File:Solar panel supported.jpg\|border]]		[[File:Solar panel supported.jpg\|border]]

	=== '''7. Attach the radar''' ===		=== '''7. Attach the radar''' ===
	Secure the radar assembly to the post by attaching the radar box to the radar‑bracket arms on the post. See Note 1 on Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 ~~CINQ EDGE~~ (SOLAR) ~~CONNECTIONS AND INSTALLATION~~].		Secure the radar assembly to the post by attaching the radar box to the radar‑bracket arms on the post. See Note 1 on Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (SOLAR) Connections and Install].

	=== '''8. Raise radar post''' ===		=== '''8. Raise radar post''' ===

	# Stand up the radar post.		# Stand up the radar post.
	# Secure the post using large U-bolts see Note 4 481515 for placement		# Secure the post using large U-bolts see Note 4 Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (Solar) Connections and Install] for placement.
	# Place U-bolts slightly above and below enclosure strut channel.		# Place U-bolts slightly above and below enclosure strut channel.

Line 154:		Line 154:
	# Drive each grounding rod 2-6 inches from the post, in the loosened soil around the post hole. (Avoid driving the grounding rods into the concrete.		# Drive each grounding rod 2-6 inches from the post, in the loosened soil around the post hole. (Avoid driving the grounding rods into the concrete.
	# Drive the rod until only 4-8 inches remain above grade.		# Drive the rod until only 4-8 inches remain above grade.
	# Cut the grounding wire in half to create two pieces with a terminal on one end. See Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 ~~CINQ EDGE GROUNDING INSTALLATION~~] for details.		# Cut the grounding wire in half to create two pieces with a terminal on one end. See Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding Installation] for details.

	=== '''10. Attach antennas''' ===		=== '''10. Attach antennas''' ===
Line 162:		Line 162:
	# Ensure the antenna brand label is upright at the top.		# Ensure the antenna brand label is upright at the top.
	# Use four bolts to secure each antenna to its bracket.		# Use four bolts to secure each antenna to its bracket.
	# Install the grounding‑wire terminal on the lower antenna bracket assembly. See Note 4 on Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 ~~CINQ EDGE GROUNDING INSTALLATION~~].		# Install the grounding‑wire terminal on the lower antenna bracket assembly. See Note 4 on Drawing [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding Installation].
	# Apply thread lubrication (anti‑seize preferred) to stainless‑steel parapanel hardware to prevent thread galling. See Note 5 on Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 ~~CINQ EDGE~~ (~~SOLAR~~) ~~CONNECTIONS AND INSTALLATION~~].		# Apply thread lubrication (anti‑seize preferred) to stainless‑steel parapanel hardware to prevent thread galling. See Note 5 on Drawing [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (Solar) Connections and Install].

	=== '''11. Install the enclosure''' ===		=== '''11. Install the enclosure''' ===
Line 169:		Line 169:
	# Position the enclosure to the near‑side post on the side away from the track.		# Position the enclosure to the near‑side post on the side away from the track.
	# From inside, loosely feed the bolts through the back of the enclosure (from inside) and thread onto the cone nuts.		# From inside, loosely feed the bolts through the back of the enclosure (from inside) and thread onto the cone nuts.
	# Slide the top and bottom cone nuts on one side into the strut ~~channel~~ channel.		# Slide the top and bottom cone nuts on one side into the strut channel.
	# Shift the inserted cone nuts slightly towards the center to create space for the opposite side.		# Shift the inserted cone nuts slightly towards the center to create space for the opposite side.
	# Slide the second set of cone nuts into the strut channel and center the enclosure.		# Slide the second set of cone nuts into the strut channel and center the enclosure.
	# Adjust the cone nuts vertically if needed.		# Adjust the cone nuts vertically if needed.
	# Secure the bolts from inside the enclosure. See Note 2 on Drawing [[Media:481515.pdf\|481515 ~~CINQ EDGE~~ (~~SOLAR~~) ~~CONNECTIONS AND INSTALLATION~~]].		# Secure the bolts from inside the enclosure. See Note 2 on Drawing [[Media:481515.pdf\|481515 Cinq Edge (Solar) Connections and Install]].

	=== '''12. Install wheel detector''' ===		=== '''12. Install wheel detector''' ===
Line 183:		Line 183:

	# Lay out the far‑side antenna conduit. Starting at the near‑side post, run the conduit through the shallow trench under the track and to the bottom of the far‑side post. Coil any slack and lay it neatly against the near‑side post.		# Lay out the far‑side antenna conduit. Starting at the near‑side post, run the conduit through the shallow trench under the track and to the bottom of the far‑side post. Coil any slack and lay it neatly against the near‑side post.
	# On both sides of the track, attach the cables and hoods to the antennas. See Note 6 on Drawing [[Media:481515.pdf\|481515 ~~CINQ EDGE~~ (~~SOLAR~~) ~~CONNECTIONS AND INSTALLATION~~]].		# On both sides of the track, attach the cables and hoods to the antennas. See Note 6 on Drawing [[Media:481515.pdf\|481515 Cinq Edge (Solar) Connections and Install]].
	# Bury the conduit by filling in the trench.		# Bury the conduit by filling in the trench.

Line 203:		Line 203:
	<div style="border:1px solid #ccc; padding:1em; margin:1em 0; background:#f9f9f9;">		<div style="border:1px solid #ccc; padding:1em; margin:1em 0; background:#f9f9f9;">
	=== <b>Verify final install checklist</b> ===		=== <b>Verify final install checklist</b> ===
	Verify the details below before completing installation. See Drawing [[Media:~~481000~~.pdf\|~~481000 CINQ EDGE~~ (~~SOLAR~~) ~~FIELD INSTALLATION GUIDE~~]] for details.		Verify the details below before completing installation. See Drawing [[Media:481001.pdf\|481001 Cinq Edge (Solar) Install Checklist]] for details.
	<ul>		<ul>
	<li>Solar panel orientation faces south or southeast.</li>		<li>Solar panel orientation faces south or southeast.</li>
Line 240:		Line 240:
	== Additional resources ==		== Additional resources ==

	* [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 Cinq Edge Solar Install Guide]		* [https://docdepot.railrsm.com/images/a/af/481000.pdf 481000 Cinq Edge (Solar) Install Guide]
	* [https://docdepot.railrsm.com/images/d/d1/481403.pdf 481403 Cinq Edge Solar Crate Disassembly]		* [https://docdepot.railrsm.com/images/1/10/481001.pdf 481001 Cinq Edge (Solar) Install Checklist]
			* [https://docdepot.railrsm.com/images/d/d1/481403.pdf 481403 Cinq Edge (Solar) Crate Disassembly]
			* [https://docdepot.railrsm.com/images/e/e7/481514.pdf 481514 Cinq Edge Grounding Install]
			* [https://docdepot.railrsm.com/images/1/1d/481515.pdf 481515 Cinq Edge (Solar) Connections and Install]
	* [[CINQ Edge User Quick Start Guide]]		* [[CINQ Edge User Quick Start Guide]]
	* [[Frauscher Wheel Detector Installation and Optimization\|Installation and Optimization]]		* [[Frauscher Wheel Detector Installation and Optimization\|Installation and Optimization]]