View source for LX-800 to T10 Upgrade Procedure

<p>The T10 is a small, high-performance, embedded computer system on a single STD-Bus board. It integrates several popular I/O options including six serial ports, digital I/O, M.2 SSD storage, USB, display port and network. The T10 is based upon an Intel Atom E900 (Apollo Lake-1) processor, supporting up to 8 GB LPDDR4 2400 MT/s system memory.</p>

The T10 is designed to replace the LX-800 in the STD bus cage of our APU-102. The document herein describes the procedure of replacing the LX-800 with the T10.<p>'''Parts:'''</p>
*'''402268: '''T10 (Wayside Processor Board)
<p>'''Other:'''</p>
*Laptop computer with capability to connect to APU-102 via ethernet port.
*Communication program such as Tera Term, HyperTerminal, Secure CRT, or any program that supports ZMODEM. This excludes Putty.

= Upgrade Procedure =
== Save Parameters From the LX-800 ==

#Connect to the APU-102 through the ethernet port.
#Log in to the supervisor menu.
#Enter the &lt;ep&gt; command to edit parameters.

{| style="border-collapse: collapse; width: 600px; margin-left: auto; margin-right: auto;" border="2px" cellpadding="4px" 
|-
| style="width: 93.6541px; background-color: rgb(230, 126, 35);" | <p style="text-align: center;" ><span style="color: rgb(255, 255, 255);" >'''ATTENTION:'''</span></p>
| style="width: 519.997px;" | <p>Be very cautious while editing parameters. Make sure to only make changes listed here.</p>
|}

#Enter the &lt;df&gt; command to begin a file download.
#Enter a name for the new file.
##For example purposes, “'''upgrade.prm'''” will be used in this document.
#Copy all the parameters to the upgrade.prm file by entering <br>&lt;zsend upgrade.prm&gt;.
#Once completed, note down the name given to the file, as the file will be transferred to the T10 later.
#Enter the &lt;dp&gt; command to display parameters.
#Navigate to Session 1 in the display parameters menu.
#Enter “3” to access AEI Report Connect.
#Locate the AccessFileName parameter and make note of what value it is set to. This is one of the files to transfer to the T10.
##For example purposes, “'''PALFTPC2.ACC'''” will be used in this document.
#Note down another file to transfer later. This file should have the same name as the file set in the AccessFileName parameter, but with a different file extension.
##For an FTP configured site, note the file extension as “.INI”.<br>e.g. '''PALFTPC2.INI'''
##For an SFTP configured site, note the file extension as “.BAT”<br>e.g. '''PALFTPC2.BAT'''
#Enter “8” to access the Ports parameter menu.
#Navigate to Ethernet.
#Note down all information listed to check against the uploaded file later.
#Enter the &lt;zsend&gt; command with the value DNSTableFileName is set to.
##For example, &lt;zsend dns.dat&gt; will send “dns.dat”.

== Remove the LX-800 and Install T10 ==

#Power down the APU-102.
#Remove all ribbon cables from the LX-800 and pull the board from the STD bus cage.
#Insert the T10 board into the STD bus cage and install ribbon cables.

{| style="border-collapse: collapse; width: 600px; margin-left: auto; margin-right: auto;" border="2px" cellpadding="2px" 
|-
| style="width: 86.0883px; background-color: rgb(230, 126, 35);" | <p style="text-align: center;" >'''&nbsp;'''<span style="color: rgb(255, 255, 255);" >'''ATTENTION:'''</span></p>
| style="width: 908.059px;" | <p>The “Component Side” is the side with the WIN SYSTEMS SOM on it.The 50 pin header is on the “BOTTOM SIDE” of the PCB with respect to a STD Card cage. <br>'''Catastrophic failures''' can happen if this is plugged into the STD Card Cage BACKWARDS (rotated 180°).</p>
|}
<p><br></p>[[image:img1736485127634.png|300px|center|frameless]]<br>[[image:img1736499105198.png|300px|center|frameless]]

== Install parameters on T10 ==

#Log in to supervisor menu.
#Confirm the files uploaded from the LX-800 are under the correct filename using the &lt;dir&gt; command.
##For example, &lt;dir upgrade.prm&gt; will search for “upgrade.prm”.
#Enter the &lt;ep&gt; command to edit parameters.
#Load the new parameters file onto the T10 using the &lt;LF&gt; command.
##For example, “LF upgrade.prm” will load “upgrade.prm”.
#Use the &lt;Esc&gt; key to navigate back to the supervisor menu.
#Enter &lt;shell commit&gt; to commit your changes.
#Reboot the APU-102.
#Log in to supervisor menu.
#Use the &lt;zrec&gt; command to receive the following files:
##Enter the filename noted from DNSTableFileName. <br>For example, &lt;zrec dns.dat&gt;
##Enter the filename noted from AccessFileName. <br>For example, &lt;zrec PALFTPC2.ACC&gt;
##Enter the corresponding AccessFileName .INI or .BAT file noted. <br>For example, &lt;zrec PALFTPC2.INI&gt; or &lt;zrec PALFTPC2.BAT&gt;.
<p><br></p>

= Verifying Changes =

#Log in to the Supervisory menu.
#Enter the &lt;dp&gt; command to display parameters.
#Navigate to Session 1 in the display parameters menu. Menus 1-5 and 7 of Session 1 will be checked.
#Enter "1" to access the Site Information. Assess if the owner information is set as desired.
#Enter "2" to access AEI Report Opts. Assess if the Host Reporting parameters are set as desired.
#Enter "3" to access AEI Report Connect. Assess if the AccessFileName parameter is set to the value noted in the previous sections. Ensure that PortFile is set to "Ethernet.dat".
#Enter "4" to access Maint Report Opts. Ensure ReportEnable is set to "1" if maintenance reports are desired.
#Enter "5" to access Maint Report Connect. Assess if the AccessFileName parameter is set as desired.
#Enter "7" to access the T94 menu. Assess if the T94 format file is set as desired.
#Navigate back to the Supervisory menu using <Esc>.
#Enter &lt;tda204&gt; to access the TDA204 menu and calibrate the null values as necessary.
#Exit the TDA204 menu, and enter the &lt;dp&gt; command to display parameters.
#Enter "7" to access the Acquisition menu.
#Enter "1" to access the wheel sensor parameters.
#Assess if the wheel sensor parameters are set as desired.

If any parameters are ''not'' set to the value desired, the <ep> command can be used to open the edit parameters menu. Parameters can be edited and navigated the same way as the display parameters menu.